Showing 71–105 of 138 resultsSorted by price: low to high
10µF, 250V polarised aluminium electrolytic capacitor for high-voltage filtering in mains power supplies, SMPS, inverters and LED drivers.
25-pin female header strip with 2.0 mm pitch, for modules and boards that use the smaller 2 mm header spacing.
40-pin female header strip with 2.0 mm pitch for modules and boards that use 2 mm header spacing.
3-pin KF301 PCB screw terminal block with 5.08 mm pitch, for secure, tool-tightened wire connections to circuit boards.
NE555P precision timer IC for time delays, oscillators, PWM and LED flasher circuits, a must-have for learners.
24-pin DIP IC socket that lets you mount and replace 24-pin chips on a PCB without desoldering.
40-pin DIP IC socket that lets you mount and replace 40-pin chips on a PCB without desoldering.
28-pin DIP IC socket that lets you mount and replace 28-pin chips on a PCB without desoldering.
20-pin DIP IC socket that lets you mount and replace 20-pin chips on a PCB without desoldering.
16-pin DIP IC socket that lets you mount and replace 16-pin chips on a PCB without desoldering.
14-pin DIP IC socket that lets you mount and replace 14-pin chips on a PCB without desoldering.
8-pin DIP IC socket for 555 timers, op-amps and EEPROMs, so chips can be swapped without desoldering.
5 mm 4-pin RGB LED that mixes red, green and blue to make almost any colour with Arduino PWM.
6-pin DIP IC socket that lets you mount and replace 6-pin chips on a PCB without desoldering.
40-pin female header strip with standard 2.54 mm spacing for connecting modules, shields and PCBs.
Hermetically sealed reed switch that opens or closes when a magnet comes near, for door and window sensors and position detection.
L7805C linear voltage regulator that provides a stable 5V output from a higher DC input, in a TO-220 package.
BC327 general-purpose PNP transistor (TO-92), the complementary partner to the BC337.
L7812CV linear voltage regulator that provides a stable 12V output from a higher DC input, in a TO-220 package.
680VAC metal oxide varistor (MOV) that clamps voltage surges to protect mains-powered circuits and equipment.
IRF540 N-channel power MOSFET (TO-220) for switching motors, LED strips and other high-current DC loads.
Slim 27 mm piezoelectric ceramic disc that makes clear sound alerts and can also sense knocks and vibration.
9 x 15 cm perf board with a grid of pre-drilled holes for soldering components into permanent, reliable prototype circuits.
Gettop 9V (6F22) non-rechargeable battery for multimeters, alarms, remote controls and electronics projects.
5kΩ single rotary potentiometer with 3 pins and a 15 mm shaft, for adjustable control in Arduino and electronics projects.
12075 DC 5V active buzzer with a built-in oscillator: just apply 5V for a beep, ideal for alarms, timers and Arduino alerts.
IRLZ44N logic-level N-channel power MOSFET that can be switched directly from 5V microcontroller pins.
5V DC SPDT 5-pin power relay that lets a low-voltage circuit switch a separate load circuit.
4-pin KF301 PCB screw terminal block with 5.08 mm pitch, for secure, tool-tightened wire connections to circuit boards.
IRFZ44N N-channel power MOSFET (TO-220) for robust, high-current switching of motors, LED strips and inverters.
100Ω, 5W cement power resistor with flame-retardant coating, for power supplies, amplifiers and dummy loads.
1kΩ single rotary potentiometer with 3 pins and a 15 mm shaft, for adjustable control in Arduino and electronics projects.
2N7000 small-signal N-channel enhancement MOSFET (TO-92) for low-current switching and logic level shifting.
74HC125D surface-mount quad buffer/line driver with 3-state outputs for compact PCB designs.
14.5 x 6.5 cm perf board with a grid of pre-drilled holes for soldering components into permanent, reliable prototype circuits.
Your Cart is Empty