Showing 1–35 of 61 resultsSorted by price: low to high
2.1 mm DC barrel power jack for adding a standard DC adapter input to boards, enclosures and devices.
Right-angle PCB-mount DC barrel power jack with an internal switch, for adding a DC power input to your boards and devices.
DC power jack adapters (male/female) with screw terminals, for quick power connections to LED strips, CCTV and projects.
Gettop 9V (6F22) non-rechargeable battery for multimeters, alarms, remote controls and electronics projects.
24V DC SPDT 5-pin power relay for switching loads in control panels, automation and vehicle circuits.
12V DC SPDT 5-pin power relay that lets a low-voltage circuit switch a separate load circuit.
AMS1117 3.3V regulator module that converts 4.5-12V DC into a stable 3.3V for ESP8266, ESP32 and sensors.
Micro USB linear charger module for single 3.7V lithium cells (e.g. 18650), with red charging and green full indicators.
AMS1117-5.0 regulator module that converts 6-12V DC into a stable 5V supply for microcontrollers and sensors.
Mini360 tiny adjustable step-down converter for powering small electronics from a higher DC supply.
Single-cell 18650 Li-ion battery holder with wire leads, to mount and connect one 18650 cell in your project.
Double 18650 battery holder with leads, to hold and connect two 18650 Li-ion cells in your project.
XT60 male connector pre-wired with 14 AWG silicone wire, a reliable high-current plug for LiPo batteries, drones and RC models.
XT60 female connector pre-wired with 14 AWG silicone wire, a reliable high-current plug for LiPo batteries, drones and RC models.
Tiny MP1584EN 3A adjustable step-down module for compact battery-powered, drone and robotics projects.
BS 1363 fused 3-pin plug top (13A fuse), the standard plug for connecting appliances to Kenyan 230V sockets.
AMS1117-3.3 regulator module that provides a stable 3.3V from a 5V supply for ESP32, ESP8266 and 3.3V sensors.
XT30 male connector pre-wired with 16 AWG silicone wire, a reliable high-current plug for LiPo batteries, drones and RC models.
XT30 female connector pre-wired with 16 AWG silicone wire, a reliable high-current plug for LiPo batteries, drones and RC models.
LM2596 adjustable DC-DC step-down (buck) module that reduces 5-32V input to a set lower voltage for your project.
5V 1-channel relay module that lets Arduino or ESP32 switch mains or DC loads (up to 250V AC / 30V DC) safely.
Black 3-cell 18650 battery holder with leads (about 77 x 62 x 20 mm), to hold three 18650 Li-ion cells side by side.
3.7V 3000mAh rechargeable lithium-ion battery for torches, power banks and portable projects.
LM2596 fixed-output step-down module that gives a stable, pre-set voltage with no adjustment needed.
Simple 12V LED power indicator module that lights up to confirm 12V DC power is present.
4-cell 18650 battery holder with leads, to keep four 18650 Li-ion cells organised and connected in your project.
5V 2-channel relay board (works with 3.3V signals) for switching two lights or appliances from Arduino, ESP32 or Raspberry Pi.
1S BMS module that protects a single 3.7V lithium cell from overcharge, over-discharge and over-current.
2S 20A BMS protection board for two 18650 lithium cells in series (7.4V nominal, 8.4V full), with overcharge, over-discharge and short-circuit protection.
XL6009 adjustable DC-DC boost module that steps a lower DC voltage up to a higher, adjustable output.
Stackable 1-channel relay shield for the Wemos D1 Mini to control lamps, fans and appliances over Wi-Fi.
Breadboard power supply module with two independently switchable 3.3V/5V rails, powered from a DC jack or USB.
Nickel strip for spot-welding 26650 lithium cells into reliable custom battery packs.
XL4015 5A adjustable step-down converter for efficiently powering motors, LED strips and electronics.
Your Cart is Empty